Sdr Usb Dongle For Mac

Jul 15, 2012  I have created an OSX Application bundled that includes HDSDR, Wine, gnuradio, grbaz and allows the user to have a functional SDR setup without the need of installing anything.

I’ve had a few of the RTL radio tuner dongles for a while. These are USB devices that were originally made for use as TV tuners overseas, but it turns out that you can access the I/Q data stream, and turn them into an SDR (Software Defined Radio).

They can be tuned roughly over a range of 25 to 1700 MHz, and sometimes even higher, depending on the tuner IC chip inside the particular dongle. I previously posted about how to get the RTL dongle working on the Mac here: and here:. These posts were from 2013, and I did the installation on a Mac running OS X 10.6, using some pre-built libraries.

Fast forward to the present day. I got a new Mac running OS X 10.11 El Capitan, and I wanted to be able to use the RTL dongles with my favorite SDR software on the Mac,. H&r block® deluxe and state 2017 tax software, for pc/mac, traditional disc. Cocoa RTL Server is a stand alone app that interfaces with an RTL dongle. It does not require you to build or install any drivers or libraries.

It just works. It’s based off of an open source app called SoftShell, that I heavily extended. Cocoa RTL Server also acts like a networked SDR, following the RF Space protocol.

That means it works with SdrDx, as well as any other SDR app on the Mac that supports RF Space SDRs like the netSDR. You can download a copy of the app from the page.

Source code is included, however I am not offering any support for the project or final app. Here’s a screenshot of the app running: Getting up and running is easy: 1. Plug in your RTL device 2. Run CocoaRTLServer 2.0 3. Select the device from the popup menu (usually it is already selected) 4. Change the rtl_tcp or tx_tcp port values if needed 5. Click Open 6.

Configure your SDR app (set the correct TCP port) and run it I’ve run it under Mac OS X 10.6, 10.10 and 10.11, It should run under 10.7-10.9 as well. It only works with RTL devices with an E4000 or R820T tuner IC. Using SdrDx, I can tune a large portion of the FM broadcast band, click to view full size: In this case I am tuned to 97.9 MHz. To the left of the signal meter, you can see it has decoded the station ID from the RDS data. Yes, SdrDx decodes RDS.

If you look at the lower right corner, you see the scope display of the demodulated FM audio. There are markers for the portions of interest: You can see the main audio above the green marker to the left.

The stereo pilot at 19 kHz (red marker). The stereo subcarrier (aquamarine) The RDS data (orange) The 67 kHz SCA subcarrier (purple) The 92 kHz SCA subcarrier (yellow) Cocoa RTL Server also includes a server that emulates rtl_tcp, so it works with which decodes aircraft transponders that transmit on 1090 MHz. It should also work with any other app that gets data from rtl_tcp. Here’s a screenshot of Cocoa1090 running.

An RTL-SDR Software Defined Radio receiver for iOS devices (requires an external rtl_tcp server). Listen to AM, FM and SSB radio signals. View a waterfall of the RF spectrum.

Connect, via the rtl_tcp network protocol, to a networked RTL-SDR USB peripheral. IOS devices do not currently support the direct connection of USB devices such as an RTL-SDR. Thus, the use of this app requires network access to a server, such as a Raspberry Pi (or Mac), with an RTL-SDR unit plugged into its USB port, and running the rtl_tcp protocol at an TCP/IP network address accessible from your iOS device. The Raspberry Pi acts, essentially, as a USB port adapter for your iOS device.